Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Were you looking for help concerning Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough project. If the old bathtub is conveniently available, the task can move speedily; if you need to open a wall surface to remove the old tub and also position the brand-new tub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Chances are you may require an expert plumber to make tube links.
This article will certainly help you set up a brand-new tub in your washroom if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Making use of both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other tap.
Switch on the supply of water and also examine all joints and new pipework for leaks and tighten them if required. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its final setting.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, leading to problems with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break rather very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our topic about Tools You Need to Install a New Bathtub . Thanks so much for taking time to read through our content. Enjoyed our entry? Please share it. Help somebody else find it. I am grateful for your time. Don't hesitate to check up our website back soon.
Book Now! Report this page